Common Sense RC

This Heavy Duty Adjustable High Current Voltage Regulator allows you to use a 2-cell 7.4V LiPo battery pack to power your servos. They react faster and with more torque. You will also get the addded benefit of consistent voltage to your servos. With a normal RX battery pack, voltage decreases, and your servos slow down as the day goes by. This unit is designed to handle 30 watts of power dissipation. Input voltage: 6.0V - 8.4VOutput voltage: 5.4V - 6.0VInput voltage must be at least 0.65V more...

This 12 volt, 5 amp A/C adapter is "plug 'n play" ready for use as a D/C input Power Supply. Comes with a Tamiya-style female connector, or you can snip off the connector and use your own.Input: 100-240V ACOutput: 12V, 5ADimensions: 4.5 x 2.4 x 1.5 in.Weight: 15.6 oz.0-ACPS5

This 2500mah Lithium Polymer pack fits all Futaba, Hitec, Airtronics and JR Transmitters that use the "Square" pack. It comes with an "RCY" type connector that is likely to work with the connector on your transmitter. If it doesn't mate up, you can cut the connector off of your existing battery and splice it to the wires on our pack. Airtronics radios cannot be charged using the charging receptacle located on the outside of the radio.Size: 25 x 30 x 95 mmWeight: 146 grams (5.15...

This 2-pack serial adapter cord with Deans-type connectors allows you to charge 2 batteries at the same time with Bantam e-stations. The 4mm banana plugs will plug directly into your Bantam charger and most other major brands. It can also be used to wire packs in series inside a vehicle. 0-WHS-2

This 3-pack serial adapter cord with Deans-type connectors allows you to charge 3 batteries at the same time with Bantam e-stations. The 4mm banana plugs will plug directly into your Bantam charger and most other major brands. It can also be used to wire packs in series inside a vehicle. 0-WHS-3

All Z-series controllers are fully programmable with the throttle stick. Amp Rating 45A Operating Range 2-5S LiPo 6-12 NiCad/NiMH BEC Current 2.2A Length 60mm Width 28mm Height 8mm Weight 1.3oz.  0-Z-45 Instructions ...

This banana plug adapter for digital volt meters comes with two small pins perfect for testing individual lipo cells. 2.5mm pin spacing fits most major lipo brands. The 4mm banana plugs fit directly into your DVM.0-DVM2PINS

0-LIGHTTUBE-3MM-20-WHITE

Perfect for High voltage/High Amp draw. Very high quality wire.Sold by the foot and by each color. If you want all colors, you need to add the first to your cart, then add the next color. 0-18AWG-BSIL

Perfect for High voltage/High Amp draw. Very high quality wire.Sold by the foot and by each color. If you want all colors, you need to add the first to your cart, then add the next color. 0-18AWG-RSIL

White shrinkwrap - 28mm wide by .16mm thick - Sold in 24" increments0-sw-w-28

  These waterproof, super-bright LED lights are a must-have accessory for anyone that needs a lighting setup that can withstand wet conditions. Each strip is encased in clear silicone and can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to...

  These waterproof, super-bright LED lights are a must-have accessory for anyone that needs a lighting setup that can withstand wet conditions. Each strip is encased in clear silicone and can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to...

For 2-Cell LiPos0-CSWIRE-2S

This adapter is to use 7.4 volt (2 cell) PolyQuest or Hyperion packs with Common Sense RC V2 products0-PQ2CS-2-V2

Great for Antweight Robots and other small wiring systems!20 Gauge silicone wire with very high strand count, easy to work with. Not quite as flexible as the Wet Noodle, but still much more 'flexy' than most wire.Sold by the foot and by each color. If you want both colors, you need to add the first to your cart, then add the next color.0C-WS20-100B

A simple 8Amp power supply will be all you need if you're just using one battery charger. 8A is enough for a max charge rate of most battery chargers. Screw terminals on the front and pre-installed power cord means this is ready to go!110V and 220V input voltage is selected by switch. Before powering on, please check input voltage to avoid damage.Input: 90-132V/185-264V ACOutput: 12V, 8ADimensions: 7.85 x 3.85 x 1.65 in.Weight: 28.4 oz.0-ACDC100W

14 Gauge silicone wire with very high strand count, easy to work with. Not quite as flexible as the Wet Noodle, but still much more 'flexy' than most wire. This is great wire to use when you don't need the thicker 12 gauge Wet Noodle wire. For medium-current applications and smaller robots.Sold by the foot and by each color. If you want all colors, you need to add the first to your cart, then add the next color. 0C-WS14AWG-YLW

Great for Antweight Robots and other small wiring systems!20 Gauge silicone wire with very high strand count, easy to work with. Not quite as flexible as the Wet Noodle, but still much more 'flexy' than most wire.Sold by the foot and by each color. If you want both colors, you need to add the first to your cart, then add the next color.0C-WS20-100R

  These super-bright LED lights are a must-have accessory for any night flyer. Each strip can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to the surface of your aircraft or vehicle. SpecsWidth: 8mmRuns off of 12 volts DC (3S lipos are...

  These waterproof, super-bright LED lights are a must-have accessory for anyone that needs a lighting setup that can withstand wet conditions. Each strip is encased in clear silicone and can easily be soldered to an adapter that fits onto the balance connector of your lipo battery. These strips can be used alone with any 3S lipo battery or linked together for unlimited possibilities and combinations. Each strip also has a strong adhesive on the back which makes them simple to install to...

0-LIGHTTUBE-3MM-40-YELLOW

This servo "Y" adapter is truly universal, with a JR/Universal connector on the receiver end and a Futaba J connector on the servo end. This means that you can plug any servo into the "Y" adapter, and plug the adapter into any receiver. These adapters are great when you need to run two servos to a single port on your receiver.0-SERVO-Y-12

This high-quality 3A UBEC switching DC-DC regulator is used when your ESC doesn't have a BEC or when your onboard BEC won't handle your needs. When supplied with a 2-6 cell lithium battery (or 5-18 cells NiMH /NiCd ), it outputs consistent, safe voltage for your receiver, gyro and servos. Provides much greater power efficiency than a linear mode UBEC.FeaturesDesigned with an advanced switch mode DC-DC regulator IC.The output is powerful even working with 4 to 6 cells lipo batteries.Battery...